Product List
- UV germicidal lamp
- Amalgam Lamps
- Standard Output Germicidal Lamps
- Preheat Start Germicidal Lamps-T5 4P
- Preheat Start Germicidal Lamps-T5 2P
- Instant Start (Slimline) Germicidal Lamps-T5 SP
- Preheat Start Germicidal Lamps-T8 2P
- UV Germicidal lamp T6 2P
- UV Germicidal lamp T4 2P
- Compact Germicidal Lamps
- H shape germicidal lamp
- U shape germicidal lamp
- High Output (HO) Germicidal Lamps
- Self-ballast Germicidal Bulbs
- Cold Cathode Germicidal Lamps
- Quartz Sleeves
- UV Air Cleaners
- Electronic Ballasts
- Stainless Steel UV Sterilizers
- Submergible UV Modules
- Mobile UV Disinfection Cart
- UV Table light
- UV Recirculator
- UV Purifier
- Specific Bases and Fittings
320W amalgam UV lamp for water treatment and air purify with 2.1A current lamp supply
Product introduction：
320W amalgam UV lamp for water treatment and air purify with 2.1A current lamp supply
- Details
- Technical Data
Classification of common electronic ballasts for low-pressure UV lamps:
According to the wiring method: plug, lead wire, integrated type (cable with power plug and lampholder).
According to input voltage:
AC series: single voltage 230VAC (220~240V)
A-single voltage 120VAC (110~120V)
U-wide voltage 110~240VAC
24VAC, etc.
DC series: DC12V and DC24V are commonly used, represented by D. Others can also be customized.
According to the startup method:
Preheat start (PH, EPS, PS series, etc.), suitable for frequently turning on/off the lamp to extend the service life of the lamp;
Instant start (PL series, etc.), suitable for normally open or normally closed application scenarios.
According to function:
LED-red/green, green indicator;
B-buzzer;
5V-0/5VDC signal;
N-dry contact, external PLC output switching value, remote monitoring lamp normal/faulty;
L-countdown, generally decreasing according to the number of days in the year, 365...000, prompting the date of lamp replacement;
T-accumulated timing, 0...9999 (H), monitors the running time of ballast and lamp;
P-Adjust the output current and lamp power through the PWM signal frequency to dimming function;
D-Adjust the output current and lamp power from 0-10V to realize the dimming function;
R-Remotely monitoring the operation/fault of the lamp through RS485, and remotely switching the lamp on/off;
C-Connect to PLC through 24VDC power supply to remotely control the lamp on/off intelligently;
S-integrated ballast is equipped with a key switch on/off;
WS-water flow switch function, connected to the water flow switch, it will turn off with a delay of 5 minutes;
PH9-2100-320
1*Lamp Type:GPHHA1000T6 GPHHA1554T6 NNI300/147XL TUV325WXPT
Wiring Diag：A
2*Lamp Type:GPHHA843T6 GPHHA357T6
Wiring Diag：B
Technical specifications
Mains Voltage：110-240VAC±10%
Mains Frequency:50/60Hz
Power Factor: >0.98
Efficiency: >94%
Operating Frequency: 40-60KHz
Starting：Preheat
Dimensions:250*95*45 mm
Only Best for You
Lamp status indication via LED indication
Green LED：Lamp on
Red LED：Lamp fault
Lamp status forwarding
Potential free relay contacts for lamp on/lamp
Lamp status indication via LED indication
Green LED：Lamp on
Red LED：Lamp fault
Lamp status forwarding
Potential free relay contacts for lamp on/lamp fault..
Installation requirement
Wire Gauge：1.0-1.5mm 2
Max.cable length between ballasts and lamp：5m
Relay contacts：potential free，load：50…500mA at 24…230V AC；
50…500mA at 5…60V DC
DC5V±5% 5mA：lamp on. DC 0V：lamp fault or on lamp. Connect LED.
DC5V±10% Max 50mA：lamp on. DC 0V：lamp fault or on lamp. Connect Relay.
Mounting restrictions
Disconnect Input Power Before Installing or Servicing.
Ballast Case Must Be Grounded.
Don’t short any two wires of the four outputs.
Applications
All areas of applications include UV lamps
=>Municipal water treatment
=>Industrial water treatment
=>Water injection for oilfield
